科技行者

行者学院 转型私董会 科技行者专题报道 网红大战科技行者

知识库

知识库 安全导航

至顶网网络频道配置带有NAT的PIX实现IPSec VPN连接

配置带有NAT的PIX实现IPSec VPN连接

  • 扫一扫
    分享文章到微信

  • 扫一扫
    关注官方公众号
    至顶头条

在此示例配置,远程PIX 通过动态主机配置协议(DHCP)收到IP地址并且连接到中央PIX。此配置允许中央PIX接受动态IPSec连接。

作者:论坛整理 来源:zdnet网络安全 2008年3月11日

关键字: 防火墙 CISCO 思科 PIX防火墙 思科PIX防火墙

  • 评论
  • 分享微博
  • 分享邮件

  前言

  在此示例配置,远程PIX 通过动态主机配置协议(DHCP)收到IP地址并且连接到中央PIX。此配置允许中央PIX接受动态IPSec连接。 远程PIX使用网络地址转换(NAT) "加入"专用地址设备在它之后对专用地址网络在中央PIX 之后。远程PIX可以首次与中央PIX (的连接知道终端),但中央PIX不可以首次与远程PIX (的连接不知道终端)。

  在此示例配置,Tiger是远程PIX和 Lion 是中央PIX。我们不了解什么Tiger的IP地址将是,因此我们必须配置Lion动态地接受连接从任何地方知道计算机通配符 ,预共享密钥。 Tiger知道什么数据流将被加密(因为由访问控制列表指定)并且Lion终点哪里被找出。 Tiger必须首次连 接。两边执行NAT和NAT 0 绕过NAT为IPSec信息数据流。

  另外,异地用户在此配置连接到中央 PIX (Lion)使用异地用户不能连接到远程PIX的 CiscoVPNClient 3.x. (Tiger)因为两边将有并且不知道在哪里发 送请求的动态地指定的IP地址。

  在您开始之前

  惯例

  欲 知关于文件惯例的更多信息,请参阅 Cisco技 术提示惯例。

  前提

  此文档没有特殊的先决 条件。

  使用的组件

  此配置使用以 下的软件及硬件版本实施了并且测试了。

  Cisco PIX防火墙软件版本6.0(1) (或极大为 Cisco VPN Client 3.x)

  Cisco PIX防 火墙软件版本5.3.1 (远程PIX)

  Cisco VPN客户端版本3.x 配置

  在此部分,您介绍用信 息配置在本文描述的功能。

  注意: 找到其它信息关于用于本文的命令,使用IOS命 令查找工具。

  网络图

  本文使用网络建立图示如下的。

  Lion配置

  Building configuration...

  : Saved

  :

  PIX Version 6.0(1)

  nameif gb-ethernet0 spare1 security10

  nameif gb-ethernet1 spare2 security15

  nameif ethernet0 outside security0

  nameif ethernet1 inside security100

  enable password 8Ry2YjIyt7RRXU24 encrypted

  passwd 2KFQnbNIdI.2KYOU encrypted

  hostname lion

  domain-name cisco.com

  fixup protocol ftp21

  fixup protocol http 80

  fixup protocol h323 1720

  fixup protocol rsh 514

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip5060

  fixup protocol skinny 2000

  names

  !

  !--- ACL to avoid Network Address Translation (NAT) on the IPSec packets

  access-list 100 permit ip 10.2.2.0 255.255.255.0 10.1.1.0 255.255.255.0

  access-list 100 permit ip 10.2.2.0 255.255.255.0 10.3.3.0 255.255.255.0

  !

  pager lines 24

  logging buffered debugging

  interface gb-ethernet0 1000auto shutdown

  interface gb-ethernet1 1000auto shutdown

  interface ethernet0 10baset

  interface ethernet1 10baset

  mtu spare1 1500

  mtu spare2 1500

  mtu outside 1500

  mtu inside 1500

  ip address spare1 127.0.0.1 255.255.255.255

  ip address spare2 127.0.0.1 255.255.255.255

  !

  !--- IP addresses on the interfaces

  ip address outside 203.1.1.1 255.255.255.0

  ip address inside 10.2.2.1 255.255.255.0

  !

  ip audit info action alarm

  ip audit attack action alarm

  ip local pool clientpool 10.3.3.1-10.3.3.10

  no failover

  failover timeout 0:00:00

  failover poll 15

  failover ip address spare1 0.0.0.0

  failover ip address spare2 0.0.0.0

  failover ip address outside 0.0.0.0

  failover ip address inside 0.0.0.0

  pdm history enable

  arp timeout 14400

  !--- global (outside) 1 203.1.1.10-203.1.1.15

  !--- Change from NAT to PAT on DHCP interface

  global (outside) 1 interface

  !

  !--- Binding ACL 100 to the NAT statement to avoid NAT on the IPSec packets

  nat (inside) 0 access-list 100

  !

  nat (inside) 1 0.0.0.0 0.0.0.0 0 0

  conduit permit icmp any any

  !

  !--- Default route to the Internet

  route outside 0.0.0.0 0.0.0.0 203.1.1.2 1

  !

  timeout xlate 3:00:00

  timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h323 0:05:00 sip

  0:30:00 sip_media 0:02:00

  timeout uauth 0:05:00 absolute

  aaa-server TACACS+ protocol tacacs+

  aaa-server RADIUS protocol radius

  no snmp-server location

  no snmp-server contact

  snmp-server community public

  no snmp-server enable traps

  floodguard enable

  !

  !--- The sysopt command avoids conduit on the IPSec encrypted traffic

  sysopt connection permit-ipsec

  !

  no sysopt route dnat

  !

  !--- Phase 2 encryption type

  crypto ipsec transform-set myset esp-des esp-md5-hmac

  crypto dynamic-map cisco 1 set transform-set myset

  crypto map dyn-map 20 ipsec-isakmp dynamic cisco

  !

  !--- Binding the IPSec engine on the outside interface

  crypto map dyn-map interface outside

  !

  !--- Enabling ISAKMP key-exchange

  isakmp enable outside

  !

  !--- ISAKMP Policy for accepting dynamic connections from remote PIX

  isakmp key ******** address 0.0.0.0 netmask 0.0.0.0

  !--- ISAKMP Policy for Cisco VPN Client 2.x

  isakmp policy 10 authentication pre-share

  isakmp policy 10 encryption des

  isakmp policy 10 hash md5

  isakmp policy 10 group 1

  isakmp policy 10 lifetime 1000

  !

  !--- ISAKMP Policy for Cisco VPN Client 3.x

  isakmp policy 20 authentication pre-share

  isakmp policy 20 encryption des

  isakmp policy 20 hash sha

  isakmp policy 20 group 2

  isakmp policy 20 lifetime 86400

  !

  !--- IPSec group configuration for either client

  vpngroup unityclient address-pool clientpool

  vpngroup unityclient dns-server 10.1.1.3

  vpngroup unityclient wins-server 10.1.1.3

  vpngroup unityclient default-domain cisco.com

  vpngroup unityclient idle-time 1800

  vpngroup unityclient password ********

  !

  telnet timeout 5

  ssh timeout 5

  terminal width 80

  Cryptochecksum:d6fe92db883a052c5765be21a74e7c8d

  : end

  [OK]

  Tiger配置

  Building configuration...

  : Saved

  :

  PIX Version 5.3(1)

  nameif gb-ethernet0 spare1 security10

  nameif gb-ethernet1 spare2 security15

  nameif ethernet0 outside security0

  nameif ethernet1 inside security100

  enable password 8Ry2YjIyt7RRXU24 encrypted

  passwd 2KFQnbNIdI.2KYOU encrypted

  hostname tiger

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 1720

  fixup protocol rsh 514

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  names

  !

  !--- ACL to avoid Network Address Translation (NAT) on the IPSec packets

  access-list 101 permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0

  !

  pager lines 24

  logging on

  no logging timestamp

  no logging standby

  no logging console

  no logging monitor

  logging buffered debugging

  no logging trap

  no logging history

  logging facility 20

  logging queue 512

  interface gb-ethernet0 1000auto shutdown

  interface gb-ethernet1 1000auto shutdown

  interface ethernet0 10baset

  interface ethernet1 10baset

  mtu spare1 1500

  mtu spare2 1500

  mtu outside 1500

  mtu inside 1500

  ip address spare1 127.0.0.1 255.255.255.255

  ip address spare2 127.0.0.1 255.255.255.255

  !

  ip address outside dhcp

  ip address inside 10.1.1.1 255.255.255.0

  !

  ip audit info action alarm

  ip audit attack action alarm

  no failover

  failover timeout 0:00:00

  failover poll 15

  failover ip address spare1 0.0.0.0

  failover ip address spare2 0.0.0.0

  failover ip address outside 0.0.0.0

  failover ip address inside 0.0.0.0

  arp timeout 14400

  global (outside) 1 204.1.1.10-204.1.1.15

  !

  !--- Binding ACL 101 to the NAT statement to avoid NAT on the IPSec packets

  nat (inside) 0 access-list 101

  !

  nat (inside) 1 0.0.0.0 0.0.0.0 0 0

  conduit permit icmp any any

  route outside 0.0.0.0 0.0.0.0 204.1.1.2 1

  timeout xlate 3:00:00

  timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h323 0:05:00 sip

  0:30:00 sip_media 0:02:00

  timeout uauth 0:05:00 absolute

  aaa-server TACACS+ protocol tacacs+

  aaa-server RADIUS protocol radius

  no snmp-server location

  no snmp-server contact

  snmp-server community public

  no snmp-server enable traps

  floodguard enable

  !

  !--- The sysopt command avoids conduit on the IPSec encrypted traffic

  sysopt connection permit-ipsec

  !

  no sysopt route dnat

  !

  !--- Phase 2 encryption type

  crypto ipsec transform-set myset esp-des esp-md5-hmac

  crypto map newmap 10 ipsec-isakmp

  crypto map newmap 10 match address 101

  crypto map newmap 10 set peer 203.1.1.1

  crypto map newmap 10 set transform-set myset

  !

  !--- Binding the IPSec engine on the outside interface

  crypto map newmap interface outside

  !

  !--- Enabling ISAKMP key-exchange

  isakmp enable outside

  !

  !--- ISAKMP Policy for connecting to Central PIX

  isakmp key ******** address 203.1.1.1 netmask 255.255.255.255

  isakmp identity hostname

  isakmp policy 10 authentication pre-share

  isakmp policy 10 encryption des

  isakmp policy 10 hash md5

  isakmp policy 10 group 1

  isakmp policy 10 lifetime 1000

  !

  telnet timeout 5

  ssh timeout 5

  terminal width 80

  Cryptochecksum:6743b7bf9476590ecd1a1a8c6d75245b

  : end

  验证

  此部分提供您能使用确 认您的配置适当地工作的信息。

  注意 : 在 配置 模式必须执行clear命令。

  clear crypto ipsec sa - 在失败的尝试以后重置IPSec协会协商VPN建立隧道。

  clear crypto isakmp sa - 在失败的尝试以后重置互联网安全协会和密钥管理协议 (ISAKMP)安全关联协商VPN建立隧道。

  show crypto engine ipsec - 显示加密的会话。

  排除故障

  此部分提供您能使用排除您的配置故障的信息。

  故障检修命 令

  在尝试任何 debug 命令之前,请参阅 重要信息关于Debug命令。

  debug crypto ipsec - 看见客户端是否协商VPN连接的IPSec部分。

  debug crypto isakmp connection - 看见对等体是否协商VPN的ISAKMP 部分

  示例“Good ”调试输出

  中央PIX 调试

  远程PIX调试

  客户端调试

  中央PIX调试

  crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1

  OAK_MM exchange

  ISAKMP (0): processing SA payload. message ID = 0

  ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy

  ISAKMP: encryption DES-CBC

  ISAKMP: hash MD5

  ISAKMP: default group 1

  ISAKMP: auth pre-share

  ISAKMP: life type in seconds

  ISAKMP: life duration (basic) of 1000

  ISAKMP (0): atts are acceptable. Next payload is 0

  ISAKMP (0): SA is doing pre-shared key authentication using id type ID_FQDN

  return status is IKMP_NO_ERROR

  crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1

  OAK_MM exchange

  ISAKMP (0): processing KE payload. message ID = 0

  ISAKMP (0): processing NONCE payload. message ID = 0

  ISAKMP (0): processing vendor id payload

  ISAKMP (0): processing vendor id payload

  ISAKMP (0): processing vendor id payload

  ISAKMP (0): speaking to another IOS box!

  return status is IKMP_NO_ERROR

  crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1

  OAK_MM exchange

  ISAKMP (0): processing ID payload. message ID = 0

  ISAKMP (0): processing HASH payload. message ID = 0

  ISAKMP (0): SA has been authenticated

  ISAKMP (0): ID payload

  next-payload : 8

  type : 2

  protocol : 17

  port : 500

  length : 10

  ISAKMP (0): Total payload length: 14

  return status is IKMP_NO_ERROR

  crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1

  OAK_QM exchange

  oakley_process_quick_mode:

  OAK_QM_IDLE

  ISAKMP (0): processing SA payload. message ID = 1223411072

  ISAKMP : Checking IPSec proposal 1

  ISAKMP: transform 1, ESP_DES

  ISAKMP: attributes in transform:

  ISAKMP: encaps is 1

  ISAKMP: SA life type in seconds

  ISAKMP: SA life duration (basic) of 28800

  ISAKMP: SA life type in kilobytes

  ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0

  ISAKMP: authenticator is HMAC-MD5

  ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): proposal part #1,

  (key eng. msg.) dest= 203.1.1.1, src= 204.1.1.1,

  dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4),

  src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),

  protocol= ESP, transform= esp-des esp-md5-hmac ,

  lifedur= 0s and 0kb,

  spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4

  ISAKMP (0): processing NONCE payload. message ID = 1223411072

  ISAKMP (0): processing ID payload. message ID = 1223411072

  ISAKMP (0): ID_IPV4_ADDR_SUBNET src 10.2.2.0/255.255.255.0 prot 0 port 0

  ISAKMP (0): processing ID payload. message ID = 1223411072

  ISAKMP (0): ID_IPV4_ADDR_SUBNET dst 10.1.1.0/255.255.255.0 prot 0 port

  0IPSEC(key_engine): got a queue event...

  IPSEC(spi_response): getting spi 0xd0e27cb6(3504503990) for SA from 204.1.1.1

  to 203.1.1.1 for prot 3

  return status is IKMP_NO_ERROR

  crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1

  OAK_QM exchange

  oakley_process_quick_mode:

  OAK_QM_AUTH_AWAIT

  ISAKMP (0): Creating IPSec SAs

  inbound SA from 204.1.1.1 to 203.1.1.1 proxy 10.2.2.0 to 10.1.1.0)

  has spi 3504503990 and conn_id 4 and flags 4

  lifetime of 28800 seconds

  lifetime of 4608000 kilobytes

  outbound SA from 203.1.1.1 to 204.1.1.1(proxy 10.1.1.0 to 10.2.2.0)

  has spi 2729504033 and conn_id 3 and flags 4

  lifetime of 28800 seconds

  lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event...

  IPSEC(initialize_sas): ,

  (key eng. msg.) dest= 203.1.1.1, src= 204.1.1.1,

  dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4),

  src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),

  protocol= ESP, transform= esp-des esp-md5-hmac ,

  lifedur= 28800s and 4608000kb,

  spi= 0xd0e27cb6(3504503990), conn_id= 4, keysize= 0, flags= 0x4

  IPSEC(initialize_sas): ,

  (key eng. msg.) src= 203.1.1.1, dest= 204.1.1.1,

  src_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4),

  dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),

  protocol= ESP, transform= esp-des esp-md5-hmac ,

  lifedur= 28800s and 4608000kb,

  spi= 0xa2b0ed21(2729504033), conn_id= 3, keysize= 0, flags= 0x4

  return status is IKMP_NO_ERROR

  远程PIX调试

  ISAKMP (0): beginning Main Mode exchange

  crypto_isakmp_process_block: src 203.1.1.1, dest 204.1.1.1

  OAK_MM exchange

  ISAKMP (0): processing SA payload. message ID = 0

  ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy

  ISAKMP: encryption DES-CBC

  ISAKMP: hash MD5

  ISAKMP: default group 1

  ISAKMP: auth pre-share

  ISAKMP: life type in seconds

  ISAKMP: life duration (basic) of 1000

  ISAKMP (0): atts are acceptable. Next payload is 0

  ISAKMP (0): SA is doing pre-shared key authentication using id type ID_FQDN

  return status is IKMP_NO_ERROR

  crypto_isakmp_process_block: src 203.1.1.1, dest 204.1.1.1

  OAK_MM exchange

  ISAKMP (0): processing KE payload. message ID = 0

  ISAKMP (0): processing NONCE payload. message ID = 0

  ISAKMP (0): processing vendor id payload

  ISAKMP (0): speaking to another IOS box!

  ISAKMP (0): ID payload

  next-payload : 8

  type : 2

  protocol : 17

  port : 500

  length : 18

  ISAKMP (0): Total payload length: 22

  return status is IKMP_NO_ERROR

  crypto_isakmp_process_block: src 203.1.1.1, dest 204.1.1.1

  OAK_MM exchange

  ISAKMP (0): processing ID payload. message ID = 0

  ISAKMP (0): processing HASH payload. message ID = 0

  ISAKMP (0): SA has been authenticated

  ISAKMP (0): beginning Quick Mode exchange, M-ID of

  1223411072:48ebc580IPSEC(key_engine):got a queue event...

  IPSEC(spi_response): getting spi 0xa2b0ed21(2729504033) for SA

  from 203.1.1.1 to 204.1.1.1 for prot 3

  return status is IKMP_NO_ERROR

  crypto_isakmp_process_block: src 203.1.1.1, dest 204.1.1.1

  OAK_QM exchange

  oakley_process_quick_mode:

  OAK_QM_IDLE

  ISAKMP (0): processing SA payload. message ID = 1223411072

  ISAKMP : Checking IPSec proposal 1

  ISAKMP: transform 1, ESP_DES

  ISAKMP: attributes in transform:

  ISAKMP: encaps is 1

  ISAKMP: SA life type in seconds

  ISAKMP: SA life duration (basic) of 28800

  ISAKMP: SA life type in kilobytes

  ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0

  ISAKMP: authenticator is HMAC-MD5

  ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): proposal part #1,

  (key eng. msg.) dest= 203.1.1.1, src= 204.1.1.1,

  dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4),

  src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),

  protocol= ESP, transform= esp-des esp-md5-hmac ,

  lifedur= 0s and 0kb,

  spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4

  ISAKMP (0): processing NONCE payload. message ID = 1223411072

  ISAKMP (0): processing ID payload. message ID = 1223411072

  ISAKMP (0): processing ID payload. message ID = 1223411072

  ISAKMP (0): Creating IPSec SAs

  inbound SA from 203.1.1.1 to 204.1.1.1 (proxy 10.1.1.0 to 10.2.2.0)

  has spi 2729504033 and conn_id 4 and flags 4

  lifetime of 28800 seconds

  lifetime of 4608000 kilobytes

  outbound SA from 204.1.1.1 to 203.1.1.1 (proxy 10.2.2.0 to 10.1.1.0)

  has spi 3504503990 and conn_id 3 and flags 4

  lifetime of 28800 seconds

  lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event...

  IPSEC(initialize_sas): ,

  (key eng. msg.) dest= 204.1.1.1, src= 203.1.1.1,

  dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),

  src_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4),

  protocol= ESP, transform= esp-des esp-md5-hmac ,

  lifedur= 28800s and 4608000kb,

  spi= 0xa2b0ed21(2729504033), conn_id= 4, keysize= 0, flags= 0x4

  IPSEC(initialize_sas): ,

  (key eng. msg.) src= 204.1.1.1, dest= 203.1.1.1,

  src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),

  dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4),

  protocol= ESP, transform= esp-des esp-md5-hmac ,

  lifedur= 28800s and 4608000kb,

  spi= 0xd0e27cb6(3504503990), conn_id= 3, keysize= 0, flags= 0x4

  return status is IKMP_NO_ERROR

  

  客户端调试

  19 16:43:20.402 06/28/01 Sev=Info/4 CM/0x63100004

  Establish secure connection using Ethernet

  20 16:43:20.402 06/28/01 Sev=Info/4 CM/0x63100025

  Attempt connection with server "203.1.1.1"

  21 16:43:20.402 06/28/01 Sev=Info/6 IKE/0x6300003B

  Attempting to establish a connection with 203.1.1.1.

  22 16:43:20.442 06/28/01 Sev=Info/4 IKE/0x63000013

  SENDING >>>ISAKMP OAK AG (SA, KE, NON, ID, VID, VID, VID) to 203.1.1.1

  23 16:43:20.452 06/28/01 Sev=Info/4 IPSEC/0x63700014

  Deleted all keys

  24 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x6300002F

  Received ISAKMP packet: peer = 203.1.1.1

  25 16:43:20.492 06/28/01 Sev=Info/4 IKE/0x63000014

  RECEIVING <<

  26 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000059

  Vendor ID payload = 12F5F28C457168A9702D9FE274CC0100

  27 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000001

  Peer is a Cisco-Unity compliant peer

  28 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000059

  Vendor ID payload = AFCAD71368A1F1C96B8696FC77570100

  29 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000001

  Peer supports DPD

  30 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000059

  Vendor ID payload = A0EB477E6627B406AA10F958254B3517

  31 16:43:20.542 06/28/01 Sev=Info/4 IKE/0x63000013

  SENDING >>>ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT) to 203.1.1.1

  32 16:43:20.542 06/28/01 Sev=Info/4 CM/0x6310000E

  Established Phase 1 SA. 1 Phase 1 SA in the system

  33 16:43:21.143 06/28/01 Sev=Info/4 IKE/0x63000013

  SENDING >>>ISAKMP OAK TRANS *(HASH, ATTR) to 203.1.1.1

  34 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x6300002F

  Received ISAKMP packet: peer = 203.1.1.1

  35 16:43:24.067 06/28/01 Sev=Info/4 IKE/0x63000014

  RECEIVING <<

  36 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x63000010

  MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.3.3.1

  37 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x63000010

  MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 10.1.1.3

  38 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x63000010

  MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NBNS(1) (a.k.a. WINS) : , value = 10.1.1.3

  39 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x6300000E

  MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = cisco.com

  40 16:43:24.067 06/28/01 Sev=Info/4 CM/0x63100018

  Mode Config data received

  41 16:43:24.668 06/28/01 Sev=Info/5 IKE/0x63000055

  Received a key request from Driver for IP address 203.1.1.1, GW IP = 203.1.1.1

  42 16:43:24.668 06/28/01 Sev=Info/4 IKE/0x63000013

  SENDING >>>ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 203.1.1.1

  43 16:43:24.668 06/28/01 Sev=Info/5 IKE/0x63000055

  Received a key request from Driver for IP address 10.10.10.255, GW IP = 203.1.1.1

  44 16:43:24.668 06/28/01 Sev=Info/4 IKE/0x63000013

  SENDING >>>ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 203.1.1.1

  45 16:43:24.668 06/28/01 Sev=Info/4 IPSEC/0x63700014

  Deleted all keys

  46 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x6300002F

  Received ISAKMP packet: peer = 203.1.1.1

  47 16:43:25.619 06/28/01 Sev=Info/4 IKE/0x63000014

  RECEIVING <<

  48 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000044

  RESPONDER-LIFETIME notify has value of 28800 seconds

  49 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000045

  RESPONDER-LIFETIME notify has value of 4608000 kb

  50 16:43:25.619 06/28/01 Sev=Info/4 IKE/0x63000013

  SENDING >>>ISAKMP OAK QM *(HASH) to 203.1.1.1

  51 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000058

  Loading IPsec SA (Message ID = 0x59515364 OUTBOUND SPI = 0xB24CDB55 INBOUND SPI = 0x83AA0042)

  52 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000025

  Loaded OUTBOUND ESP SPI: 0xB24CDB55

  53 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000026

  Loaded INBOUND ESP SPI: 0x83AA0042

  54 16:43:25.619 06/28/01 Sev=Info/4 CM/0x63100019

  One secure connection established

  55 16:43:25.629 06/28/01 Sev=Info/6 DIALER/0x63300003

  Connection established.

  56 16:43:25.669 06/28/01 Sev=Info/6 DIALER/0x63300008

  MAPI32 Information - Outlooknot default mail client

  57 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x6300002F

  Received ISAKMP packet: peer = 203.1.1.1

  58 16:43:25.960 06/28/01 Sev=Info/4 IKE/0x63000014

  RECEIVING <<

  59 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000044

  RESPONDER-LIFETIME notify has value of 28800 seconds

  60 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000045

  RESPONDER-LIFETIME notify has value of 4608000 kb

  61 16:43:25.960 06/28/01 Sev=Info/4 IKE/0x63000013

  SENDING >>>ISAKMP OAK QM *(HASH) to 203.1.1.1

  62 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000058

  Loading IPsec SA (Message ID = 0x23A23005 OUTBOUND SPI = 0xAD0599DB INBOUND SPI = 0x2B74D4A4)

  63 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000025

  Loaded OUTBOUND ESP SPI: 0xAD0599DB

  64 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000026

  Loaded INBOUND ESP SPI: 0x2B74D4A4

  65 16:43:25.960 06/28/01 Sev=Info/4 CM/0x63100021

  Additional Phase 2 SA established.

  66 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x63700010

  Created a new key structure

  67 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x6370000F

  Added key with SPI=0x55db4cb2 into key list

  68 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x63700010

  Created a new key structure

  69 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x6370000F

  Added key with SPI=0x4200aa83 into key list

  70 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x63700010

  Created a new key structure

  71 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x6370000F

  Added key with SPI=0xdb9905ad into key list

  72 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x63700010

  Created a new key structure

  73 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x6370000F

  Added key with SPI=0xa4d4742b into key list

  74 16:43:35.173 06/28/01 Sev=Info/6 IKE/0x6300003D

  Sending DPD request to 203.1.1.1, seq# = 1856135987

  75 16:43:35.173 06/28/01 Sev=Info/4 IKE/0x63000013

  SENDING >>>ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 203.1.1.1

  76 16:43:35.173 06/28/01 Sev=Info/5 IKE/0x6300002F

  Received ISAKMP packet: peer = 203.1.1.1

  77 16:43:35.173 06/28/01 Sev=Info/4 IKE/0x63000014

  RECEIVING <<

  78 16:43:35.173 06/28/01 Sev=Info/5 IKE/0x6300003F

  Received DPD ACK from 203.1.1.1, seq# received = 1856135987, seq# expected = 1856135987

    • 评论
    • 分享微博
    • 分享邮件
    邮件订阅

    如果您非常迫切的想了解IT领域最新产品与技术信息,那么订阅至顶网技术邮件将是您的最佳途径之一。

    重磅专题
    往期文章
    最新文章