安装，配置rp-pppoe拨号软件，使adsl成功上网

　　1.下载rp-pppoe-3.5

　　2。解压和安装：

　　#tar zxvf rp-pppoe-3.5.tar.gz

　　进入解压目录执行

　　#sh ./go

　　3。配置

　　然后再来设置ADSL。这一处，我们要用命令。

　　#adsl-setup

　　Welcome to the Roaring Penguin ADSL client setup. First, I will run

　　some checks on your system to make sure the PPPoE client is installed

　　properly...

　　Looks good! Now, please enter some information:

　　USER NAME

　　>>>Enter your PPPoE user name (default XXX): 在这里输入ADSL的用户名

　　INTERFACE

　　>>>Enter the Ethernet interface connected to the ADSL modem

　　For Solaris, this is likely to be something like /dev/hme0.

　　For Linux, it will be ethn, where 'n' is a number.

　　(default eth0):如果一张网卡就设置写上eth0

　　Do you want the link to come up on demand, or stay up continuously?

　　If you want it to come up on demand, enter the idle time in seconds

　　after which the link should be dropped. If you want the link to

　　stay up permanently, enter 'no' (two letters, lower-case.)

　　NOTE: Demand-activated links do not interact well with dynamic IP

　　addresses. You may have some problems with demand-activated links.

　　>>>Enter the demand value (default no):不用写什么

　　DNS

　　Please enter the IP address of your ISP's primary DNS server.

　　If your ISP claims that 'the server will provide DNS addresses',

　　enter 'server' (all lower-case) here.

　　If you just press enter, I will assume you know what you are

　　doing and not modify your DNS setup.

　　>>>Enter the DNS information here:在这里写上202.96.134.133

　　下一个DNS是202.96.168.68 //这里根据个人不同可以修改

　　----------------------------------------------------------

　　本文出处http://linux-down.kmip.net ，如需转载请注明！

　　点击http://linux-down.kmip.net免费下载大量的linux学习资料,软件!

　　----------------------------------------------------------

　　PASSWORD

　　>>>Please enter your PPPoE password:输入密码

　　>>>Please re-enter your PPPoE password:再输入一次

　　FIREWALLING

　　Please choose the firewall rules to use. Note that these rules are

　　very basic. You are strongly encouraged to use a more sophisticated

　　firewall setup; however, these will provide basic security. If you

　　are running any servers on your machine, you must choose 'NONE' and

　　set up firewalling yourself. Otherwise, the firewall rules will deny

　　access to all standard servers like Web, e-mail, ftp, etc. If you

　　are using SSH, the rules will block outgoing SSH connections which

　　allocate a privileged source port.

　　The firewall choices are:

　　0 - NONE: This script will not set any firewall rules. You are responsible

　　for ensuring the security of your machine. You are STRONGLY

　　recommended to use some kind of firewall rules.

　　1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation

　　2 - MASQUERADE: Appropriate for a machine acting as an Internetgateway

　　for a LAN

　　>>>Choose a type of firewall (0-2):这里添写为2

　　** Summary of what you entered **

　　Ethernet Interface: eth0

　　User name: XXX

　　Activate-on-demand: No

　　DNS: Do not adjust

　　Firewalling: MASQUERADE

　　>>>Accept these settings and adjust configuration files (y/n)?

　　弄完后，就按一个y键。

　　不要急于连接,REBOOT -N

　　然后进入网络设置,设置ETH1固定IP，停止ETH1(我的是用他)

　　然后ADSL-START

　　PING 你的DNS,如果可以,那么,恭喜你!

　　如果不行，REBOOT -N

　　ADSL-START,这下没问题啦，尽情享受吧！