扫一扫
分享文章到微信
扫一扫
关注官方公众号
至顶头条
Cisco 单臂路由详细如下:
C2900交换机：
switch>en
switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)#exit
switch#vlan database
switch(vlan)#vlan 2 name xiaofam2
switch(vlan)#vlan 3 name xiaofam3
switch(vlan)#exit
switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)#int f0/8
switch(config-if)#switchport mode trunk
switch(config-if)#switchport ?
access vlan
mode trunk
trunk allowed vlan
trunk encap dot1q
switch(config-if)#switchport trunk ?
allowed vlan
encapsulation dot1q
switch(config-if)#switchport trunk encapsulation dot1q
switch(config-if)#exit
switch(config)#int f0/1
switch(config-if)#switchport mode access
switch(config-if)#switchport access vlan 2
switch(config-if)#exit
switch(config)#int f0/2
switch(config-if)#switchport mode access
switch(config-if)#switchport access vlan 3
switch(config-if)#exit
switch(config)#exit
switch#show vlan
Vlan Name Status Ports
------- -------- ---------- ------------------------
1 default Active F0/3, F0/4, F0/5, F0/6, F0/7
2 xiaofam2 Active F0/1
3 xiaofam3 Active F0/2
1002 fddi-d Active
1004 fnet-d Active
VLAN Type SAID MTU
-------- ------- -------------- --------
1 enet 100001 1500
1002 fddi 101002 1500
1002 fnet 101003 1500
switch#
2621路由器：
router>en
router#config
?
router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
router(config)#int f0/0
router(config-if)#no shut
router(config-if)#exit
router(config)#exit
router#show run
Building configuration...
Current configuration : 729 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname
!
enable secret $1$3Ws&^f
enable password
!
ip subnet-zero
no ip routing
!
!
!
!
!
interface FastEthernet0/0
!
!
no ip mroute-cache
half-duplex
!
!
interface FastEthernet0/1
!
!
no ip mroute-cache
duplex auto
shutdown
!
interface Serial0/0
!
!
no ip mroute-cache
!
shutdown
!
interface Serial0/1
!
!
no ip mroute-cache
!
shutdown
!bt4破解无线网络
ip classless
no ip http server
ip pim bidir-enable
!
snmp-server community public RO
!
line con 0
password
line aux 0
line vty 0 4
password
!
!
end
router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
router(config)#int f0/0.1
router(config-subif.1)#ip addr 192.168.10.1 255.255.255.0
router(config-subif.1)#?
router(config-subif.1)#encapsulation ?
router(config-subif.1)#encapsulation dot1q 2 native
router(config-subif.1)#exit
router(config--if)#exit
router(config)#int f0/0.2
router(config-subif.2)#ip addr 192.168.20.1 255.255.255.0
router(config-subif.2)#encapsulation dot1q 3 native
router(config-subif.2)#exit
router(config--if)#exit
router#show run
Building configuration...
Current configuration : 729 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname
!
enable secret $1$3Ws&^f
enable password
!
ip subnet-zero
no ip routing
!
!
!
!
!
interface FastEthernet0/0
f0/0.1 ip: 192.168.10.1 255.255.255.0 dot1q : e
f0/0.2 ip: 192.168.20.1 255.255.255.0 dot1q : e
no ip mroute-cache
half-duplex
!
!
interface FastEthernet0/1
!
!
no ip mroute-cache
duplex auto
shutdown
!
interface Serial0/0
!
!
no ip mroute-cache
!
shutdown
!
interface Serial0/1
!
!
no ip mroute-cache
!
shutdown
!
ip classless
no ip http server
ip pim bidir-enable
!
snmp-server community public RO
!
line con 0
password
line aux 0
line vty 0 4
password
!
!
end
router#show run
Building configuration...
Current configuration : 729 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname
!
enable secret $1$3Ws&^f
enable password
!
ip subnet-zero
no ip routing
!
!
!
!
!
interface FastEthernet0/0
f0/0.1 ip: 192.168.10.1 255.255.255.0 dot1q : e
f0/0.2 ip: 192.168.20.1 255.255.255.0 dot1q : e
no ip mroute-cache
half-duplex
!
!
interface FastEthernet0/1
!
!
no ip mroute-cache
duplex auto
shutdown
!
interface Serial0/0
!
!
no ip mroute-cache
!
shutdown
!
interface Serial0/1
!
!
no ip mroute-cache
!
shutdown
!
ip classless
no ip http server
ip pim bidir-enable
!
snmp-server community public RO
!
line con 0
password
line aux 0
line vty 0 4
password
!
!
end
router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
router(config)#ip routing
router(config)#
另外，配置两个PC，，分别为
192。168。10。2 /24 gw:192.168.10.1
192.168.20.2/24 gw:192.168.20.1
如果您非常迫切的想了解IT领域最新产品与技术信息，那么订阅至顶网技术邮件将是您的最佳途径之一。
京公网安备 11010802021500号